Black Box IC108A Guia de Instalação

Hardware Installation Guiderevision 1 — 14330 ISC CommunicationThe following information can be used to configure communication for Lenel controllers

ISC Communications152 — revision 1

Hardware Installation Guiderevision 1 — 15330.4.2 Security EnhancementsPast installations may have contained vulnerabilities which could lead to unaut

ISC Communications154 — revision 1After the firmware upgrade has been completed, disable port 77FE to prevent unauthorized access to this device.Other

Hardware Installation Guiderevision 1 — 155• LNL-ETHLAN-MICR with firmware version 5.4 If Micro-100 unit's power is cycled,the unit will not res

ISC Communications156 — revision 12. Start HyperTerminal. The Connection Description window will open with the “New Connection” setting. (Choose New C

Hardware Installation Guiderevision 1 — 15710. The software will next ask you if you wish to set the gateway. Answer yes and type the gateway IP addre

ISC Communications158 — revision 1Step 2: Entering the Serial Port Setup Menu1. Type 1 and then press the <Enter> key to enter the serial port s

Hardware Installation Guiderevision 1 — 1593. You will now be back at the setup screen. Type 9 and then press the <Enter> key to save the setup

ISC Communications160 — revision 1ISC to Lantronix CoBox Token Ring Serial Server ConfigurationTOKEN RING NETWORK9-pin female2 3 5

Hardware Installation Guiderevision 1 — 16130.6 Lantronix CoBox-DRThe ISC can alternatively be connected to the Lantronix CoBox-DR unit. Use the follo

ISC Communications144 — revision 1The latest version of EZWebCon can be downloaded from the Lantronix website (www.lantronix.com). For detailed inform

ISC Communications162 — revision 1ACDCACGNDGNDGNDIN2IN1 A B CJ9J14232 4 852W 4WJ1TXDTR1+RXDTR1-RTSR1+CTSR1-GNDTR2+TR2-

Hardware Installation Guiderevision 1 — 163To configure the server and channel 1, refer to the following screenshots. Information is available for hex

ISC Communications164 — revision 1SDS1100 to ISC, 2-wire RS-485A C D CA CGN DGN DGN DI N2I N1 A B CJ9J14232 48 52W 4WJ1TX DTR 1

Hardware Installation Guiderevision 1 — 165SDS1100 to ISC, 4-wire RS-485A C D CA CGN DGN DGN DI N2I N1 A B CJ9J14232 48 52W

ISC Communications166 — revision 130.7.1 Configuration of the SDS1100/1101/CoBox-FLTo configure this Lantronix device, perform the following procedure

Hardware Installation Guiderevision 1 — 167Server configurationa. IP Address. If DHCP is not used to assign IP addresses, enter the IP address manuall

ISC Communications168 — revision 1c. Flow. Flow control sets the local handshaking method for stopping serial input/output. The default setting is 00.

Hardware Installation Guiderevision 1 — 169Step 1: Establish a serial connection with ETHLANWith the power OFF on the UDS device, establish a serial c

ISC Communications170 — revision 16. You can close your current HyperTerminal session.Step 3: Configure the UDS ETHLAN Make sure that the device is po

Hardware Installation Guiderevision 1 — 1719. At this point, make sure that switch 5 on the ISC is configured correctly for hardware flow control. It

Hardware Installation Guiderevision 1 — 1455. At this point, press the <Enter> key. (It may take a few seconds to complete booting).• Power shou

ISC Communications172 — revision 1Wiring for RS-232 4-wire.Ports 1 and 6 wiring configuration for 4-wire (RS-232)ISC 25-pin connectorTXD/TR1+ Pin 2RXD

Hardware Installation Guiderevision 1 — 173A C DCA CGNDGNDGNDI N2I N1 A B CJ9J14232 48 52W 4WJ1TXDTR1+RX DTR1-RTSR1+CTSR1-GNDTR2

ISC Communications174 — revision 1Unit Setup (RS-232 4-wire)As of March 2004, the current firmware version is 4.5. Connect to the unit via Telnet thro

Hardware Installation Guiderevision 1 — 175A C D CA CGNDGNDGNDIN2IN1 A B CJ9J1 4232 48 52W 4WJ1TXDTR1+RX DTR1-RTSR1+CTSR1-GNDTR

ISC Communications176 — revision 1Unit Setup (RS-485 2-wire)As of March 2004, the current firmware version is 4.5. Connect to the unit via Telnet thro

Hardware Installation Guiderevision 1 — 1779 or 25 Pin Connector5 2 3 7 3 2DB 9 Pin Male DB 25 Pin FemaleWorkstation (PC)R

ISC Communications146 — revision 130.2.3 Configuring the ETHLANAny additional changes specific to the hardware that the Lantronix box is connecting to

Hardware Installation Guiderevision 1 — 14712. For flow control, type:change flow control [FLOW CONTROL]and press <Enter>, where [FLOW CONTROL]

ISC Communications148 — revision 1Note: The ARP/ping method only works during the first two minutes of LNL-ETHLAN-MICR operation. If this process is n

Hardware Installation Guiderevision 1 — 149Richco plastic P/N LMSP-7-0130.4 CoBox Micro 100The CoBox Micro 100 device plugs directly into the LNL-2000

ISC Communications150 — revision 14. Telnet to the assigned IP address and port 1, this should fail quickly (2-3 seconds). This will force CoBox Micro

Hardware Installation Guiderevision 1 — 151n. Send Char 2 = 00When these changes have been made, type ‘9’ at the main screen to save the changes and e