Black-box 16 port Manual do Utilizador Página 160
- Página / 263
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Black Box Console Server user guide 160
reboot
user level:
admin
This command will reboot the unit. You will be asked to confirm the reboot with the
following prompt:
save config to flash ROM y/n
If you press ‘y’ the unit will save your configuration, close all connections and then
reboot. If you press ‘n’ the unit will prompt you:
confirm reboot unit y/n
Press ‘y’ to reboot, ‘n’ to cancel.
For more information on how the unit reboots, see BOOTP, Appendix F BOOTP.
Rebooting does not reset the unit to factory default settings.
Syntax reboot
Menu
equivalent
Network Configuration - Reboot
See also show server
reset factory
user level:
admin
This command will reset the unit to its default values. The unit will save the factory
default settings to FLASH memory; this saving will take a few seconds. After this
period you will be logged out and presented with a new login prompt.
Syntax reset factory
Menu
equivalent
Network Configuration - Reset
See also reboot
reset line
user level:
admin
This command will reset the specified serial line(s) to the default line configuration.
Syntax resetline./n /*
Where:
. specifies the current line.
n is a specific serial line number.
- User Guide 1
- INSTRUCCIONES DE SEGURIDAD 2
- About this Guide 5
- Fast Contents 6
- Contents 7
- Chapter 1 Introduction 17
- About the Console Server 18
- Typical applications summary 20
- Chapter 2 Installation 23
- of unit 27
- LED guide 29
- Console Server 30
- Setting up an IP address 33
- About DHCP 35
- • Set up procedure on page 39 38
- Set up procedure 39
- Setting up the host table 46
- Changing a Host 48
- Deleting a host 49
- Changing the Admin Password 50
- RADIUS configuration 51
- RADIUS parameters description 54
- DNS configuration 56
- WINS configuration 57
- Configuring network gateways 58
- Adding a gateway 59
- Deleting a Gateway 60
- Saving configuration changes 62
- Saving to a file 63
- Setting date and time 64
- Performing a soft reboot 65
- Security 70
- Lost password 73
- Configuring a dial in line 74
- Setting up the line 75
- Configuring SLIP 78
- Configuring PPP 81
- PPP form field descriptions 82
- ROAMING 90
- Configuring a modem 92
- Configuring users 93
- Adding a user account 98
- Configuring a user account 99
- User form field descriptions 100
- CALLBACK 104
- About user levels 107
- CLI prompts 107
- Changing a user’s password 108
- Deleting a user account 108
- Resetting the line to default 110
- Saving your settings 111
- Chapter 4 Using your Console 115
- Introduction 116
- Information required 117
- Access procedure 117
- Accessing devices via SSH 118
- Required Information 120
- Appendix A Cabling 125
- RJ45 RS232 serial ports 126
- AUI port 128
- RJ45 10/100BaseT port 129
- Admin Port 130
- Direct (1:1) Connections 131
- Sun Microsystem servers 132
- Black Box 833AS 134
- IBM RS6000 135
- PC serial port 136
- RXD 2 <——————— 3 TXD 137
- GND 7 ———————— 5 GND 137
- Terminals 138
- Direct connections 140
- Appendix B The CLI 141
- CLI commands 142
- Equivalent: 157
- (not available) 157
- See Also: netload, save 157
- See also 165
- [raw/telnet/ssh][raw/telnet] 166
- See also show ppp line 171
- ~break', where 179
- See also set line, show user 190
- See also 195
- Appendix C SNMP 203
- Overview 204
- Configuring SNMP support 205
- ADDRESS TYPE PERMISSIONS 208
- Private MIB definitions 209
- Network management 213
- Editing the 214
- Routing 214
- Appendix D Upgrading your 215
- Using TFTP from a host 217
- TFTP configuration 218
- Writing to FLASH memory 219
- Using BOOTP from a boothost 220
- Disable BOOTP/DHCP 221
- Appendix E Summary of Line 223
- Service Types 223
- List of line service types 224
- Appendix F BOOTP 227
- How BOOTP works 229
- How to setup BOOTP 231
- The bootfile 234
- Disabling the BOOTP reply 236
- Booting multiple units 238
- Multiple BOOTP servers 240
- Example of BOOTP 240
- Appendix G JETset 243
- Introduction to JETset 244
- Using JETset 246
- JETset program summary 249
- Appendix H Troubleshooting 251
- General communication matters 252
- Host problems 253
- JETset problems 254
- Login problems 255
- Problems with terminals 257
- Emergency recovery 258
- Problems with framed Routing 258
Manuais e produtos relacionados com Hardware Black-box 16 port
Hardware Black-box RS-449 Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Black-box PS035A Manual do Utilizador
(30 páginas)
(30 páginas)
Hardware Black-box GEH-6510 Manual do Utilizador
(92 páginas)
(92 páginas)
Hardware Black-box IC136C Manual do Utilizador
(23 páginas)
(23 páginas)
Hardware Black-box RM 415A Manual do Utilizador
(1 páginas)
(1 páginas)
Hardware Black-box EVNSL17A Manual do Utilizador
(1 páginas)
(1 páginas)
Hardware Black-box 21834 Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Black-box LRU4240 Manual do Utilizador
(218 páginas)
(218 páginas)
Hardware Black-box CAT5E Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Black-box CAT6a Manual do Utilizador
(2 páginas)
(2 páginas)
Hardware Black-box Modem Manual do Utilizador
(3 páginas)
(3 páginas)
Hardware Black-box COMPACT T1 Manual do Utilizador
(42 páginas)
(42 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.095 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais