Black Box IC109A-R2 Manual de Instalação Página 16
- Página / 164
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
10
© 2007 Schneider Electric. All Rights Reserved.
1
63230-216-229-B1
Installation
Equipment Identification
Package Contents
The following items are packaged separately with each Sepam™:
b One Sepam™ Series 80 base unit, with memory cartridge and two connectors
and tightened
b One or two CCA 630s (or CCA634s) for CTs
v or CCA671 for LPCTs
v OR CCT640 for extra VTs
b Two 20-point ring lug type terminal blocks (CCA620) for control power, ground
sensor input, and four main unit outputs
b One battery
b Eight spring clips
b One terminal block identification label
b Instruction materials (see below)
Optional accessories such as modules, current input connectors, and cables are
delivered in separate packages.
Note : Sepam™ SFT2841 software ships separately, even if it is ordered at the same time.
Identification of the Base Unit
To identify a Sepam™, inspect the three labels located behind the front door of the
panel board. A base unit hardware label is on the back of the door.
DE10376
The two labels below are mounted on the cartridge:
DE50534
DE50535
Cartridge hardware reference label The software reference label identifies the
specific application and working language.
Accessory Identification
Accessories — such as optional modules, current or voltage connectors and
connection cables — come in separate packages and are identified by labels.
DE50724
MSA141 Module Identification Label Example
SEPAM™ 80 LABEL
Label for units sold in US
A 4-alpha suffix denotes a deviation from
one or more of these standard features:
b Second language = US English
*
b Connection for current input
b Terminal blocks for A and E for ring
lugs (see diagram on page 16)
For example, SQM87A-UFLR has one
LPCT connector
Note : The second language will be US
English; the default language will be UK
English
A
E
C
Serial Number
Reference Number
Commercial Name
0624138
59707+01+0624138+C23
SEPAM Series 80
SQ1 S80A
24/48/125/250 Vdc
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais