Black Box IC109A-R2 Manual de Instalação Página 22
- Página / 164
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
16
© 2007 Schneider Electric. All Rights Reserved.
1
63230-216-229-B1
Installation
Base Unit
Mounting
Spring Clip Mounting Direction
The direction the spring clips are mounted depends on
the thickness of the mounting frame. The top clips are
mounted in the opposite direction to the bottom clips.
Base Unit Flush-Mounting
The Sepam™ Series 80 uses eight spring clips to frame mount the unit.
The mounting surface must be flat and stiff to guarantee tightness.
DANGER
DE80101
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
b Only qualified electrical workers should install this equipment. Such work
should be performed only after reading this entire set of instructions.
b NEVER work alone.
b Turn off all power supplying the power meter and the equipment in which
it is installed before working on it. Consider all sources of power,
including the possibility of backfeeding.
b Always use a properly rated voltage sensing device to confirm that all
power is off.
Failure to follow these instructions will result in death or serious injury.
DE50726DE50727
Mounting notches
Spring clips
Setting
Positioning
Locking
Unlocking
PE50110
Attaching the Terminal Block Identification Label
A sticker showing the rear panel of Sepam™ and terminal assignments comes with
each base unit to help connect Sepam™ and the MES120 input/output modules.
This label is usually on the side of an MES120 module or on a side panel of Sepam™
(usually the right side or bottom).
Refer to the figures above and perform the following steps to mount the base unit:
1 Shut off all power sources for the equipment cubicle.
2 Locate the mounting notches at the top and bottom of the case
3 Determine clip mounting direction based on the panel sheet thickness.
4 Compress and latch the spring clips.
5 Insert the case into the prepared cut-out of the cubicle and insert spring clips in
the notches at the top and bottom.
6 Squeeze to release and lock the latched clips and hold relay to panel.
7 To unlock the clip and remove the case, press the end of each clip toward the
panel.
Terminal block identification label
0.06 in
0.16 in
0.06 in
0.16 in
3
4
5
5
2
4x
1
4x
1
4x
2
4x
6
1
2
3
4
5
6
1
2
3
4
5
6
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais